Español
Bush Knotter Gear Warm 7852163 Replacement Knotter Assembly Part For Massey Ferguson MF1843 N/S & Challenger LB34BXD
bush knotter gear warm 7852163
,baler knotter assembly part
,mf1843 n/s knotter assembly part
Basic Properties
Trading Properties
In short: Bush Knotter Gear Warm 7852163 is a knotter system component that forms and ties the knot at the end of each bale for Massey Ferguson MF1843 N/S & Challenger LB34BXD large square balers. Aftermarket replacement, 1 1 piece minimum order, T/T payment, 7-15 days delivery.
Reference number 7852163 corresponds to a knotter system component that forms and ties the knot at the end of each bale. This replacement is produced to fit the same position on Massey Ferguson and Challenger large square balers, so it can be fitted with the standard tooling and fixings.
It is fitted to the knotter and needle assembly. The knotter stack on a square baler is a timed mechanism: needles lift the twine, bill hooks rotate, and the knot is cut and released within one cycle. Every part in that chain depends on the others being in tolerance, which is why wear here rarely stays local for long. Because the item is inexpensive relative to the downtime it can cause, many workshops keep one or two in stock alongside other service parts for the same machine family.
Key features- Profile and timing surfaces matched to the original so the knotter cycle stays in sequence.
- Wear surfaces hardened for the repeated cycling of the knotter stack.
- Replaceable as a single item, with the mounting faces ready for direct installation.
- Fits Massey Ferguson MF1843 N/S. See the compatibility table for the full list of machines.
- Packed with rust preventive protection and labelled with the reference number for easy receiving checks.
- Minimum order one 1 piece, payment by T/T, standard delivery 7-15 days.
| AGCO Part No. | 7852163 |
|---|---|
| Description (EN) | Bush Knotter Gear Warm |
| Part Type | Knotters & Needles |
| Unit | 1 piece |
| Net Weight | Not specified by the factory data sheet |
| Place of Origin | China |
| Minimum Order | 1 1 piece |
| Payment Terms | T/T |
| Delivery Time | 7-15 days |
| Supply Ability | 500 pieces per month |
| Packing | Carton with rust preventive wrap, palletised for export |
| Brand | Machine models |
|---|---|
| Massey Ferguson | MF1843 N/S, MF2150, MF2170, MF1835, MF1839, MF1841, MF1837, MF2170XD, MF2270, MF2270XD, MF2250, MF2290, MF1844 N Small Square (old), MF1838 Small Square (old), MF1836 |
| Challenger | LB34BXD, 2270XD, CHLB34B, SB36, CHLB34, C |
- Check needle timing and knotter brake action after fitting any knotter part.
- Confirm the twine path is clear and the twine discs grip evenly.
- Inspect the neighbouring parts in the same cycle, since a worn arm or anvil is often what caused the failure.
- Run a few bales and check knot quality on both sides of the bale before full field work.
- Keep the knotter area clean; packed chaff is a common cause of repeat missed ties.
A: 7852163 is listed for Massey Ferguson: MF1843 N/S, MF2150, MF2170, MF1835, MF1839, MF1841, MF1837, MF2170XD; Challenger: LB34BXD, 2270XD, CHLB34B, SB36, CHLB34, C. Confirm your model and serial range with us if the machine has been repaired before with non standard parts.
A: No. It is an aftermarket replacement manufactured to fit machines that use reference 7852163. It is supplied as a cost effective alternative for maintenance and repair work.
A: It is a knotter system component that forms and ties the knot at the end of each bale. The knotter stack on a square baler is a timed mechanism: needles lift the twine, bill hooks rotate, and the knot is cut and released within one cycle. Every part in that chain depends on the others being in tolerance, which is why wear here rarely stays local for long.
A: Send us your machine model, serial range and a photo of the existing part. We check the reference number and the visual details against the listing before you commit to an order.
A: Minimum order is one 1 piece, payment by T/T, delivery normally 7-15 days after payment confirmation, with supply capacity of around 500 pieces per month.
A: If the failure is wear of this component, yes. If timing or twine tension is out of adjustment, that has to be set as well, so check the whole knotter cycle when fitting.
Send us your part number, machine model and quantity, and we will confirm price, packing and lead time. Mixed orders combining this knotter assembly part with knotter parts, needles, knives and feeder dogs from the same machine family can be consolidated into one shipment.
