Español
Roller Chain 70921050 Replacement Driveline Component For ASME / ANSI NUMBER ANSI B29.1 & CHAIN SIZE 60 Baler
roller chain 70921050
,baler driveline component
,ansi b29.1 driveline component
Basic Properties
Trading Properties
In short: Roller Chain 70921050 is a transmission component that carries drive torque from the tractor through to the working assemblies for ASME / ANSI NUMBER ANSI B29.1 & CHAIN SIZE 60 large square balers. Aftermarket replacement, 1 1 piece minimum order, T/T payment, 7-15 days delivery.
Part 70921050 is a transmission component that carries drive torque from the tractor through to the working assemblies. It is listed for ASME / ANSI NUMBER and CHAIN SIZE large square balers and is supplied as an aftermarket replacement matched to reference number 70921050.
In service it belongs to the drive and transmission group of components. Drive components on a square baler transmit torque from the PTO and gearbox to the plunger, stuffer and knotters. Because the machine works in bursts, these parts see shock loads as well as steady torque, and any wear is multiplied through the assembly. Contractors running several machines of the same family often order a small quantity, since one reference covers the whole fleet.
Key features- Splines, keyways or tapers machined to the original dimensions for correct seating.
- Section and material suited to the shock loads of baler duty.
- Supplied ready to fit, with the mating surfaces protected for transport.
- Fits ASME / ANSI NUMBER ANSI B29.1. See the compatibility table for the full list of machines.
- Packed with rust preventive protection and labelled with the reference number for easy receiving checks.
- Minimum order one 1 piece, payment by T/T, standard delivery 7-15 days.
| AGCO Part No. | 70921050 |
|---|---|
| Description (EN) | Roller Chain |
| Part Type | Drivetrain Parts |
| Unit | 1 piece |
| Net Weight | Not specified by the factory data sheet |
| Place of Origin | China |
| Minimum Order | 1 1 piece |
| Payment Terms | T/T |
| Delivery Time | 7-15 days |
| Supply Ability | 500 pieces per month |
| Packing | Carton with rust preventive wrap, palletised for export |
| Brand | Machine models |
|---|---|
| ASME / ANSI NUMBER | ANSI B29.1 |
| CHAIN SIZE | 60 |
| CHAIN LENGTH_NUMBER OF PITCHES | 160 |
| CHAIN PITCH | 0.75 IN |
| CHAIN ROLLER WIDTH | 0.5 IN |
| CHAIN ROLLER DIAMETER | 0.469 IN |
| CHAIN PIN / HOLE DIAMETER | 0.234 IN |
| CHAIN LINK PLATE THICKNESS | 0.094 IN |
- Check backlash and end float after fitting and compare with the service manual.
- Clean splines and tapers before assembly and apply the specified lubricant or retaining compound.
- Confirm the part is seated fully on its taper or spline before torquing.
- Run the machine unloaded and listen for a change in noise level before loading it.
- Investigate the cause of failure: a seized bearing or misaligned housing will damage the new part.
A: 70921050 is listed for ASME / ANSI NUMBER: ANSI B29.1; CHAIN SIZE: 60; CHAIN LENGTH_NUMBER OF PITCHES: 160; CHAIN PITCH: 0.75 IN; CHAIN ROLLER WIDTH: 0.5 IN; CHAIN ROLLER DIAMETER: 0.469 IN; CHAIN PIN / HOLE DIAMETER: 0.234 IN; CHAIN LINK PLATE THICKNESS: 0.094 IN. Confirm your model and serial range with us if the machine has been repaired before with non standard parts.
A: No. It is an aftermarket replacement manufactured to fit machines that use reference 70921050. It is supplied as a cost effective alternative for maintenance and repair work.
A: It is a transmission component that carries drive torque from the tractor through to the working assemblies. Drive components on a square baler transmit torque from the PTO and gearbox to the plunger, stuffer and knotters. Because the machine works in bursts, these parts see shock loads as well as steady torque, and any wear is multiplied through the assembly.
A: Send us your machine model, serial range and a photo of the existing part. We check the reference number and the visual details against the listing before you commit to an order.
A: Minimum order is one 1 piece, payment by T/T, delivery normally 7-15 days after payment confirmation, with supply capacity of around 500 pieces per month.
A: Components are machined to the original profile. For high-speed or high-load applications, tell us your operating conditions so we can confirm suitability.
Send us your part number, machine model and quantity, and we will confirm price, packing and lead time. Mixed orders combining this driveline component with knotter parts, needles, knives and feeder dogs from the same machine family can be consolidated into one shipment.
