Español
Gas Strut Chassis 700720031 Replacement Hydraulic Part For END FITTING TYPE (A) (CYL END) BALL SOCKET
gas strut chassis 700720031
,baler hydraulic part
,ball socket hydraulic part
Basic Properties
Trading Properties
In short: Gas Strut Chassis 700720031 is a hydraulic or fluid line component that carries pressure or routes fluid at a junction for END FITTING TYPE (A) (CYL END) BALL SOCKET & END FITTING TYPE (B) (RAM END) BALL SOCKET large square balers. Aftermarket replacement, 1 1 piece minimum order, T/T payment, 7-15 days delivery.
700720031 is the reference used for a hydraulic or fluid line component that carries pressure or routes fluid at a junction on END FITTING TYPE (A) (CYL END) and END FITTING TYPE (B) (RAM END) square balers. We supply it as an aftermarket part, dimensionally matched to the original so it installs in the same location without modification.
The part sits in the hydraulic and line routing area of the baler. Hydraulic and line components on a square baler route fluid and air under pressure. Joints and hoses see vibration, heat and pressure pulses, so sealing faces and thread condition decide whether the assembly stays dry through a season. Because the item is inexpensive relative to the downtime it can cause, many workshops keep one or two in stock alongside other service parts for the same machine family.
Key features- Threads and seat machined for a clean seal without excess sealant.
- Body sized to keep line routing tight to the frame.
- Surface protected against corrosion in damp working conditions.
- Fits END FITTING TYPE (A) (CYL END) BALL SOCKET. See the compatibility table for the full list of machines.
- Packed with rust preventive protection and labelled with the reference number for easy receiving checks.
- Minimum order one 1 piece, payment by T/T, standard delivery 7-15 days.
| AGCO Part No. | 700720031 |
|---|---|
| Description (EN) | Gas Strut Chassis |
| Part Type | Hydraulic & Hose Fittings |
| Unit | 1 piece |
| Net Weight | Not specified by the factory data sheet |
| Place of Origin | China |
| Minimum Order | 1 1 piece |
| Payment Terms | T/T |
| Delivery Time | 7-15 days |
| Supply Ability | 500 pieces per month |
| Packing | Carton with rust preventive wrap, palletised for export |
| Brand | Machine models |
|---|---|
| END FITTING TYPE (A) (CYL END) | BALL SOCKET |
| END FITTING TYPE (B) (RAM END) | BALL SOCKET |
- Check the port count, thread size and seat type against the old part before fitting.
- Clean both mating faces and inspect the threads; never force a fitting into a damaged port.
- Tighten to the torque in the service manual, then run a short cycle and check for weeping.
- Check line clamps and supports in the same area, since vibration is the usual cause of failure.
- Use the specified fluid and bleed the circuit if the repair opened it.
A: 700720031 is listed for END FITTING TYPE (A) (CYL END): BALL SOCKET; END FITTING TYPE (B) (RAM END): BALL SOCKET. Confirm your model and serial range with us if the machine has been repaired before with non standard parts.
A: No. It is an aftermarket replacement manufactured to fit machines that use reference 700720031. It is supplied as a cost effective alternative for maintenance and repair work.
A: It is a hydraulic or fluid line component that carries pressure or routes fluid at a junction. Hydraulic and line components on a square baler route fluid and air under pressure. Joints and hoses see vibration, heat and pressure pulses, so sealing faces and thread condition decide whether the assembly stays dry through a season.
A: Send us your machine model, serial range and a photo of the existing part. We check the reference number and the visual details against the listing before you commit to an order.
A: Minimum order is one 1 piece, payment by T/T, delivery normally 7-15 days after payment confirmation, with supply capacity of around 500 pieces per month.
A: Seals are supplied as shown in the listing. If you need a specific seal material or a full seal kit, tell us the fluid and operating temperature.
Send us your part number, machine model and quantity, and we will confirm price, packing and lead time. Mixed orders combining this hydraulic part with knotter parts, needles, knives and feeder dogs from the same machine family can be consolidated into one shipment.
