Español
Tapered Roller Bearing Cone 70341230 Replacement Bearing And Seal Part For Massey Ferguson 9816 VE & Challenger 9816 VE
tapered roller bearing cone 70341230
,baler bearing and seal part
,9816 ve bearing and seal part
Basic Properties
Trading Properties
In short: Tapered Roller Bearing Cone 70341230 is a bearing, bush or seal that supports a rotating shaft or keeps lubricant in and contamination out for Massey Ferguson 9816 VE & Challenger 9816 VE large square balers. Aftermarket replacement, 1 1 piece minimum order, T/T payment, 7-15 days delivery.
70341230 is the reference used for a bearing, bush or seal that supports a rotating shaft or keeps lubricant in and contamination out on Massey Ferguson and Challenger square balers. We supply it as an aftermarket part, dimensionally matched to the original so it installs in the same location without modification.
In service it belongs to the rotating shaft support group of components. Rotating assemblies on a square baler such as the packer, stuffer and knotter shafts run in bearings and are protected by seals. These parts carry radial load and exclude dust, chaff and wash water, so their condition controls how long the shaft and housing last. Because the item is inexpensive relative to the downtime it can cause, many workshops keep one or two in stock alongside other service parts for the same machine family.
Key features- Housing and shaft fits matched to the original so the part is not loose or over-tight.
- Sealing lip and dust exclusion designed for chaff and wash-down conditions.
- Supplied clean and ready to install with standard tools.
- Fits Massey Ferguson 9816 VE. See the compatibility table for the full list of machines.
- Packed with rust preventive protection and labelled with the reference number for easy receiving checks.
- Minimum order one 1 piece, payment by T/T, standard delivery 7-15 days.
| AGCO Part No. | 70341230 |
|---|---|
| Description (EN) | Tapered Roller Bearing Cone |
| Part Type | Bearings & Seals |
| Unit | 1 piece |
| Net Weight | Not specified by the factory data sheet |
| Place of Origin | China |
| Minimum Order | 1 1 piece |
| Payment Terms | T/T |
| Delivery Time | 7-15 days |
| Supply Ability | 500 pieces per month |
| Packing | Carton with rust preventive wrap, palletised for export |
| Brand | Machine models |
|---|---|
| Massey Ferguson | 9816 VE, MF5200, MF1756, MF1734, MF1745 Round Baler (old), MF5100, MF1844 N Small Square (old), 9824 VE, MF9435, MF1843 N/S, MF2150, MF2170, MF2170XD, MF2250, MF2270, MF2270XD, MF2290 |
| Challenger | 9816 VE, 9824 VE, LB34BXD |
- Clean the shaft seat and housing bore before pressing in a new bearing or seal.
- Press on the race that is being fitted, never through the rolling elements.
- Lubricate the seal lip and the shaft before assembly so the lip does not run dry on start-up.
- Check shaft end float and alignment after fitting; a misaligned housing shortens bearing life sharply.
- Re-grease to the schedule and check for weeping within the first hours of operation.
A: 70341230 is listed for Massey Ferguson: 9816 VE, MF5200, MF1756, MF1734, MF1745 Round Baler (old), MF5100, MF1844 N Small Square (old), 9824 VE; Challenger: 9816 VE, 9824 VE, LB34BXD. Confirm your model and serial range with us if the machine has been repaired before with non standard parts.
A: No. It is an aftermarket replacement manufactured to fit machines that use reference 70341230. It is supplied as a cost effective alternative for maintenance and repair work.
A: It is a bearing, bush or seal that supports a rotating shaft or keeps lubricant in and contamination out. Rotating assemblies on a square baler such as the packer, stuffer and knotter shafts run in bearings and are protected by seals. These parts carry radial load and exclude dust, chaff and wash water, so their condition controls how long the shaft and housing last.
A: Send us your machine model, serial range and a photo of the existing part. We check the reference number and the visual details against the listing before you commit to an order.
A: Minimum order is one 1 piece, payment by T/T, delivery normally 7-15 days after payment confirmation, with supply capacity of around 500 pieces per month.
A: Bearings are supplied with standard preservative grease. Add the lubricant specified in your service manual for the application before running the machine.
Send us your part number, machine model and quantity, and we will confirm price, packing and lead time. Mixed orders combining this bearing and seal part with knotter parts, needles, knives and feeder dogs from the same machine family can be consolidated into one shipment.
