Español
Rocker Switch 700189954 Replacement Electrical Part For Massey Ferguson MF2170XD & Challenger LB34BXD Baler
rocker switch 700189954
,baler electrical part
,mf2170xd electrical part
Basic Properties
Trading Properties
In short: Rocker Switch 700189954 is an electrical component that provides lighting, switching or signalling on the machine for Massey Ferguson MF2170XD & Challenger LB34BXD large square balers. Aftermarket replacement, 1 1 piece minimum order, T/T payment, 7-15 days delivery.
Reference number 700189954 corresponds to an electrical component that provides lighting, switching or signalling on the machine. This replacement is produced to fit the same position on Massey Ferguson and Challenger large square balers, so it can be fitted with the standard tooling and fixings.
The part sits in the electrical and lighting area of the baler. Electrical parts on a square baler work in dust, vibration and wash-down conditions. Connectors corrode and switches wear, and because these parts are usually diagnostic rather than load bearing, a failure is often traced late. Because the item is inexpensive relative to the downtime it can cause, many workshops keep one or two in stock alongside other service parts for the same machine family.
Key features- Connector type and terminal layout matched to the machine loom.
- Housing and seal designed for dusty and wet working conditions.
- Rating suited to the circuit it serves.
- Fits Massey Ferguson MF2170XD. See the compatibility table for the full list of machines.
- Packed with rust preventive protection and labelled with the reference number for easy receiving checks.
- Minimum order one 1 piece, payment by T/T, standard delivery 7-15 days.
| AGCO Part No. | 700189954 |
|---|---|
| Description (EN) | ROCKER SWITCH |
| Part Type | Electrical Parts |
| Unit | 1 piece |
| Net Weight | Not specified by the factory data sheet |
| Place of Origin | China |
| Minimum Order | 1 1 piece |
| Payment Terms | T/T |
| Delivery Time | 7-15 days |
| Supply Ability | 500 pieces per month |
| Packing | Carton with rust preventive wrap, palletised for export |
| Brand | Machine models |
|---|---|
| Massey Ferguson | MF2170XD, MF2250, MF2270, MF2290, MF2270XD, MF2150, MF2170 |
| Challenger | LB34BXD, 2270XD, CHLB34B, CHLB44B |
- Compare connector type and terminal layout with the old part before fitting.
- Check the loom for chafing and the earth return before blaming the component.
- Seal connectors with the specified grease to keep water out of the terminal cavity.
- Test operation through a full cycle, including in wet conditions if the machine works outside.
- Note the operating voltage and current rating against the circuit it serves.
A: 700189954 is listed for Massey Ferguson: MF2170XD, MF2250, MF2270, MF2290, MF2270XD, MF2150, MF2170; Challenger: LB34BXD, 2270XD, CHLB34B, CHLB44B. Confirm your model and serial range with us if the machine has been repaired before with non standard parts.
A: No. It is an aftermarket replacement manufactured to fit machines that use reference 700189954. It is supplied as a cost effective alternative for maintenance and repair work.
A: It is an electrical component that provides lighting, switching or signalling on the machine. Electrical parts on a square baler work in dust, vibration and wash-down conditions. Connectors corrode and switches wear, and because these parts are usually diagnostic rather than load bearing, a failure is often traced late.
A: Send us your machine model, serial range and a photo of the existing part. We check the reference number and the visual details against the listing before you commit to an order.
A: Minimum order is one 1 piece, payment by T/T, delivery normally 7-15 days after payment confirmation, with supply capacity of around 500 pieces per month.
A: Tell us the machine model and system voltage and we will confirm the rating before you order.
Send us your part number, machine model and quantity, and we will confirm price, packing and lead time. Mixed orders combining this electrical part with knotter parts, needles, knives and feeder dogs from the same machine family can be consolidated into one shipment.
