Español
Fitting 528708 Replacement Hydraulic Part For Challenger MFHTD9 & Massey Ferguson MF2150 Baler
fitting 528708
,baler hydraulic part
,mfhtd9 hydraulic part
Basic Properties
Trading Properties
In short: Fitting 528708 is a hydraulic or fluid line component that carries pressure or routes fluid at a junction for Challenger MFHTD9 & Massey Ferguson MF2150 large square balers. Aftermarket replacement, 1 1 piece minimum order, T/T payment, 7-15 days delivery.
Reference number 528708 corresponds to a hydraulic or fluid line component that carries pressure or routes fluid at a junction. This replacement is produced to fit the same position on Challenger and Massey Ferguson large square balers, so it can be fitted with the standard tooling and fixings.
It is fitted to the hydraulic and line routing assembly. Hydraulic and line components on a square baler route fluid and air under pressure. Joints and hoses see vibration, heat and pressure pulses, so sealing faces and thread condition decide whether the assembly stays dry through a season. Dealers usually hold it together with the related parts that wear in the same area, so a repair is not delayed waiting for a small component.
Key features- Threads and seat machined for a clean seal without excess sealant.
- Body sized to keep line routing tight to the frame.
- Surface protected against corrosion in damp working conditions.
- Fits Challenger MFHTD9. See the compatibility table for the full list of machines.
- Packed with rust preventive protection and labelled with the reference number for easy receiving checks.
- Minimum order one 1 piece, payment by T/T, standard delivery 7-15 days.
| AGCO Part No. | 528708 |
|---|---|
| Description (EN) | FITTING |
| Part Type | Hydraulic & Hose Fittings |
| Unit | 1 piece |
| Net Weight | Not specified by the factory data sheet |
| Place of Origin | China |
| Minimum Order | 1 1 piece |
| Payment Terms | T/T |
| Delivery Time | 7-15 days |
| Supply Ability | 500 pieces per month |
| Packing | Carton with rust preventive wrap, palletised for export |
| Brand | Machine models |
|---|---|
| Challenger | MFHTD9, LB34BXD, 2270XD, CHLB34B, CHLB44B |
| Massey Ferguson | MF2150, MF2170, MF2170XD, MF2270, MF2270XD, MF2250, MF2290, MF1329, MF1300 |
- Check the port count, thread size and seat type against the old part before fitting.
- Clean both mating faces and inspect the threads; never force a fitting into a damaged port.
- Tighten to the torque in the service manual, then run a short cycle and check for weeping.
- Check line clamps and supports in the same area, since vibration is the usual cause of failure.
- Use the specified fluid and bleed the circuit if the repair opened it.
A: 528708 is listed for Challenger: MFHTD9, LB34BXD, 2270XD, CHLB34B, CHLB44B; Massey Ferguson: MF2150, MF2170, MF2170XD, MF2270, MF2270XD, MF2250, MF2290, MF1329. Confirm your model and serial range with us if the machine has been repaired before with non standard parts.
A: No. It is an aftermarket replacement manufactured to fit machines that use reference 528708. It is supplied as a cost effective alternative for maintenance and repair work.
A: It is a hydraulic or fluid line component that carries pressure or routes fluid at a junction. Hydraulic and line components on a square baler route fluid and air under pressure. Joints and hoses see vibration, heat and pressure pulses, so sealing faces and thread condition decide whether the assembly stays dry through a season.
A: Send us your machine model, serial range and a photo of the existing part. We check the reference number and the visual details against the listing before you commit to an order.
A: Minimum order is one 1 piece, payment by T/T, delivery normally 7-15 days after payment confirmation, with supply capacity of around 500 pieces per month.
A: Seals are supplied as shown in the listing. If you need a specific seal material or a full seal kit, tell us the fluid and operating temperature.
Send us your part number, machine model and quantity, and we will confirm price, packing and lead time. Mixed orders combining this hydraulic part with knotter parts, needles, knives and feeder dogs from the same machine family can be consolidated into one shipment.
