Español
CROSS PORT KIT 700727931
cross port kit 700727931
,baler hydraulic cross fitting
,MF2270XD cross port kit
Basic Properties
Trading Properties
In short: cross port kit 700727931 is a four way cross fitting kit for Massey Ferguson MF 2150-MF 2290 and Challenger LB34BXD / 2270XD large square balers. Aftermarket replacement, 1 kit minimum order, T/T payment, 7-15 days delivery.
Cross port kit 700727931 is a four way cross fitting kit used on Massey Ferguson and Challenger large square balers. It joins and routes lines at a junction point in the machine assembly, and is a service item that is replaced when a fitting is damaged, seized or leaking during maintenance.
Each kit is supplied ready to install. Threads and port faces are machined so the fitting seats cleanly, which matters on a baler where vibration and dust work loose on joints that do not sit flat. The kit is packed with rust preventive wrap for export and can be combined with other parts from the same machine family in one shipment.
Where the cross port kit is usedOn large square balers the knotter and stuffer assemblies rely on a compact network of lines and junction points. A cross port body provides a single four way junction, so line routing stays tight to the frame and the number of separate joints is kept to a minimum.
Because the part is small and inexpensive relative to the downtime it can cause, workshops normally keep one or two kits on the shelf alongside other service items for the same machine family.
Key features- Part number 700727931 cross port kit, supplied as a complete kit ready to install on the baler.
- Fits the Massey Ferguson MF 2150, MF 2170, MF 2170XD, MF 2270, MF 2270XD, MF 2250 and MF 2290 large square balers.
- Also fits Challenger LB34BXD, 2270XD, CH LB34B and CH LB44B models that share the same knotter frame platform.
- Four way cross port body keeps line routing compact, reducing joints and potential leak points in the assembly.
- Threads and port faces machined for a clean seal, so the kit seats without excess sealant or re tapping.
- Packed with rust preventive wrap for export, one kit per carton, minimum order quantity one piece.
| AGCO Part No. | 700727931 |
|---|---|
| Description (EN) | CROSS PORT KIT |
| Part Type | Cross port kit / four way fitting kit |
| Unit | 1 kit |
| Net Weight | Not specified by the factory data sheet |
| Finish | Anti corrosion coated |
| Place of Origin | China |
| Minimum Order | 1 kit |
| Payment Terms | T/T |
| Delivery Time | 7-15 days |
| Supply Ability | 500 kits per month |
| Packing | Carton with rust preventive wrap, palletised for export |
| Brand | Machine models |
|---|---|
| Massey Ferguson | MF 2150, MF 2170, MF 2170XD, MF 2270, MF 2270XD, MF 2250, MF 2290 |
| Challenger | LB34BXD, 2270XD, CH LB34, CH LB34B, CH LB44B |
- Compare the new kit with the removed part before installation: port count, thread size and port spacing should match.
- Clean the mating faces and check the threads for damage; do not force a fitting into a damaged port.
- Follow the torque values in your machine service manual. As a general rule, snug the fitting first, then torque in stages.
- Run the machine through a short cycle and check for weeping at the joints before returning to full field work.
- If the original fitting failed through vibration, check the line clamps and supports in the same area.
A: Cross port kit 700727931 is listed for Massey Ferguson MF 2150, MF 2170, MF 2170XD, MF 2250, MF 2270, MF 2270XD and MF 2290 large square balers, and for Challenger LB34BXD, 2270XD, CH LB34 and CH LB44B models.
A: It is the four way cross fitting used to join and route lines at a junction point in the baler assembly. Using a single cross body instead of several tees keeps the routing compact and reduces the number of joints that can leak or vibrate loose.
A: No. This is an aftermarket replacement part manufactured to fit machines that use AGCO reference 700727931. We supply it as a cost effective alternative for maintenance and repair work.
A: Send us your machine model, serial range and a photo of the existing fitting. Where a baler has been repaired before with non standard parts, the photo lets us confirm the thread and port layout before you order.
A: One kit. Standard production lead time is 7 to 15 days after payment confirmation, and we can supply up to 500 kits per month for scheduled maintenance programmes.
A: Yes. Single kit and small trial orders are welcome so you can check the thread fit and port layout on your own machine before committing to a season stock order.
Send us your part number, machine model and quantity, and we will confirm price, packing and lead time. Mixed orders combining cross port kits with knotter parts, needles, knives and feeder dogs from the same machine family can be consolidated into one shipment.
